Screwdriver to open ps4

Screwdriver to open ps4 DEFAULT

If you are making the game console disassembly for the first time in your life, pay attention to this tutorial — First time repairing

Step-by-step guide for disassembling the PlayStation 4 game console of the first model, the so-called FAT revision, which includes the following ps4 models: CUHA, CUHA, CUHA, CUHA, CUHA, CUH, CUH A, CUHB.

The serial number and model number of PS4 you can found on the gaming system, as well as on the box. At the end of the page, there is a video instruction on how to assemble the PS4 after disassembly.

To disassemble the PS4 you will need two types of screwdrivers:

  • Torx T8 / T9
  • Phillips PH0 / PH1 Also
  • Tweezer &#; will be useful

In this step-by-step instruction, we will disassemble the ps4 for cleaning and replacing the thermal paste, also you can replace any components, for example, how to remove hard drive, power supply or fan. If during the disassembly process it is not clear how to perform step, you can see the step-by-step video instruction below.

Guide How to disassemble PS4

Remove the top panel of the PS4 case. It is easy to remove, just pull up until the clamps open.


Remove one screw that fixes hard drive basket. In addition, remove the hard drive.

On the backside of the PS4, where the connection ports are located, remove stickers, and below them screws that we need to unscrew.


Now unscrew the four screws, and for this use the T8 Torx screwdriver.


Next, remove the cover of the PS4 case. Start to open the case from the same side.


On the backside of cover, you can see dust. Use a brush or napkin for cleaning the case from dust.

Let&#;s remove the power supply of PS4 game console. First, unscrew three screws T8 Torx. Then unscrew two screws using PH0 screwdriver.


Disconnect four-wire connector from the power supply. The connector is fixed quite tightly, and if you cannot get it as easily, to disconnect the cable use tweezers.


Next, using a plastic tool, pull up on the right side, then on the left side. The right side of the power supply will be harder to pull up.


If there is a lot of dust inside the power supply, it is better to remove this dust. To do this, unscrew the two screws on the power supply and open it for cleaning.

Disconnect the blue-ray drive cable from the PS4 motherboard. To do this, press the tweezers onto the iron plate and pull the cable to the side.


Next, unplug the optical drive power connector by lifting it up. In addition, disconnect the Wi-Fi antenna from the motherboard.


Remove the two screws securing the top cover to the PS4.


Grab underneath of the top cover near the power button. Pull up&#;you will hear it click as you pull up. Move to opposite side of the top cover PS4 and pull up here as well. After, just lift up cover.


Remove 12 T8 Torx screws (marked in yellow). 

Using PH0 screwdriver and unscrew the last two screws (marked in red).

Disconnect the fan cable from the motherboard (marked in green). The cable turned off by lifting up.


Next, remove the top metal panel. Now pay attention to the thermal pads, it is very important not to lose them when removing the panel.


Gently lift up PS4 motherboard. Also, pay attention to the thermal pads and be careful, do not lose them if they fall. Remove the old thermal paste from metal panel and from the CPU on the PS4 motherboard.


Apply a small amount of thermal paste to the surface of CPU. Next, distribute the thermal paste on entire surface of CPU.

Use plastic or wooden object, not metal.


Now move on to cleaning the cooling system from dust. Remove three screws on the metal panel.


After lift up the metal panel. With the brush, remove dust from the radiator.


The next step is to clean the fan. To do this, you need to unscrew the two screws, and now the fan you can remove and clean from dust.


Clean fan from dust using a brush.


Disassembly is finished, now we need to assembly everything back. Watch the video guide on PS4 assembly.

PS4 assembly

General steps:

  1. Install the fan cable into the PS4 case and secure two screws.
  2. Install the panel with a radiator and securing three screws.
  3. Install the PlayStation 4 motherboard on the metal panel in the PS4 case. Pay attention to the thermal pads that everyone would be in place.
  4. Next, install the second metal plate on the PS4 motherboard. Also, check the thermal pads.
  5. Install the holder screwing the bolts evenly, a few turns on each side.
  6. Take a Torx T8 screwdriver and secure 12 screws.
  7. Connect the wire from the fan to the motherboard.
  8. Install the bottom plastic panel of the PlayStation 4 case.
  9. Fasten two screws.
  10. Install the hard drive in the PS4 case and secure one screw.
  11. Install the glossy top cover of the PS4.
  12. Connect the optical drive power cable to the PS4 motherboard.
  13. Connect the Wi-Fi antenna to the PS4 motherboard.
  14. Connect the blue-ray drive cable to the PlayStation 4 motherboard.
  15. Connect the wire to the power supply and install the power supply in the PlayStation 4 case.
  16. Take two long screws, install them in the power supply and secure with a PH0 or PH1 screwdriver.
  17. Next, take the Torx T8 and secure three screws on the case of the PlayStation 4 power supply.
  18. Install up the rear plastic cover of the PlayStation 4.
  19. Fasten the Torx T8 screws on the rear end of the PS4 case.
  20. PS4 assembled!


This information is provided for informational purposes only. We accept no liability for damage caused to your device while following the video instructions. Also note that if your laptop or any other device is still under warranty period, then in the process of dismantling the guarantee may be canceled because traces remain after disassembly and it violates the terms of the warranty period. Before disassembling, make sure that the warranty on your laptop has been over.


What Screwdrivers You Need For Your PS4 Toolkit?

Screwdriver to open PS4

If you are a PS4 fan then I can be % sure that you love your PS4 madly. Many of us PS4 lovers have prepared a small tool kit for our beloved PS4 in case of emergency. We almost know every tool that is required for PS4, but in this article, I am going to tell you the screwdrivers that are used in the opening of PS4, PS4 controller, and PS4 hard drive.

Screwdriver plays the most vital role in the opening of the PS4 and its equipment. The reason for this is that the PS4 is completely assembled with the help of very tiny and variable screws that is why they need specific screwdrivers and must be handled very carefully.


What Screwdriver To Open PS4?

You cannot take any screwdriver for unfastening the screws of your PS4. When you will look at your PS4 you will observe screws that should be technically handled. For these screws, we use a Torx TR9 screwdriver.

If you are planning to repair or cleaning the dust from your PS4 then the TR9 Torx security screwdriver is a perfect choice. It comes with great features such as, it is durable, it is tip-resistant, it is precision screwdriver, you won’t face any hassle, it fits accurately, and you won’t face any strip.

This TR9 Torx is not letting you miss any of your screws because it comes with the Magnetic tip that is going to hold your screw so that you don’t drop it or misplace it. It has a comfortable grip that will not let you put pressure on your PS4 without causing any damage while unfastening the screw.

How To Open Your PS4?

The procedure of opening the screws of the PS4 is very simple. You just need to follow few steps. I am precisely going to mention the steps that can help you.

  • You need to completely shut down and unplug your PS4 before you plan to open it.
  • You need to remove all the stickers from your PS4. The reason for removing the stickers is that on PS4 the screws are placed behind the stickers. So, for reaching out to the screws you need to remove all the stickers.
  • Once the stickers are removed you need to use your T9 Torx screwdriver for removing the screws. The screws are very short and delicate so you don’t need much effort. You must take care that you should not strip them and once you have removed the screws keep them aside in a secure place.
  • Same screwdriver the T9 torx along with a careful procedure will be followed by you to place the screws back to their places.

What Screwdriver To Open PS4 Controller?

No controller, no gaming. The controller is a core part of a PS4. Many of us get comfortable with one controller and we love to use it whenever we are playing a game. But if this controller is not working properly, we all try to fix it first before going for another. So, for fixing it we need to open the PS4 controller. But the question is what screwdriver must be used to open the PS4 controller.

You cannot use the same screwdriver for opening the controller that you have used for opening the PS4. The screws on the controller are very tiny and specially made. Thus, you need Philips head screwdriver #0. The screwdriver is easily available and you must make it a part of your PS4 Toolkit.

You can easily find this screwdriver but you need to make sure that it offers certain features such as; the grip of the screwdriver should be cushioned so that you don’t put more effort and pressure on the controller, it should give you precise control and optimum rotation, and the tip should be magnetic and heat treated.

Points to remember:

You need to be very careful while you are taking the controller apart. The screws are very soft and you need to be very careful while unscrewing them so that you don’t strip the rest of the screws.

  • When you are unscrewing you need to push the screwdriver in the middle of the screw and start twisting slowly.
  • You need to keep twisting until you feel any resistance but if you feel that you need more pressure then don’t force it much.
  • You can use pliers for a good grip and the removal of the rest of the screw once you have slightly unscrewed the screw.
  • It might be a pressurized task for unscrewing the screw of the controllers but putting them back is quite easy and you will only need the screwdriver for doing it.

PS:  The controllers pop open so you need to be very careful when you pull the two halves apart.

What Screwdriver To Open PS4 Hard Drive?

Most of PS4 lovers always tend to upgrade or replace their hard drives. This task is done from time to time thus it is very important to know which screwdriver to be used for unscrewing the screws for getting to the hard drive. For the screws for reaching out to the hard drive the screwdriver, Phillips Head #0 is required.

You won’t find many screws for unfastening to reach the hard drive thus this task is very easy. Philip head screwdriver #0 is very easy to find and it is a must addition to the PS4 toolkit because the same screwdriver is used for opening the PS4 controller. You need to make this screwdriver an essential part of your toolkit if you are a PS4 lover and you often tend to upgrade or replace your hard drive.

A simple guide to open a hard disk:

Here I would like a small step-to-step guide that will help you in opening your hard drive.

  • Next to the Ethernet port, you will find a plastic panel that must be covering your hard drive. You need to remove this plastic panel first.
  • You will find one large screw and you need to use your crosshead screwdriver while holding your hard drive caddy in one place. 
  • Once the screw is out you need to use your fingers for pulling the caddy out of the PS4.
  • You will find four small screws that should be unscrewed for driving the hard drive out of the caddy.
  • After inserting the new hard drive, you will fasten the small screws back into their place and put the caddy back where you took it out from.


The pro gamers always take care of their PS4. Many of the Gamers have prepared their special toolkits for repairing and upgrading their PS4. But always make sure that you use the right screwdrivers for all of the screws in your PS4 because once the screw is stripped it is very difficult to put it back as it gets loose.

Read More:

  1. Alameda county sheriffs office
  2. Modern warfare update today
  3. American flag cross stitch kit

How to Clean the Dust From a Noisy PS4: A Step-by-Step Guide

If you've had a PlayStation 4 for a while, chances are that it runs a lot louder than it did when you bought it. Like most devices, dust tends to build up over time inside the system.

To keep your PS4 running at its best, it's wise to clean your system every once in a while. To quiet it down and remove all that nasty dust buildup, follow our guide to cleaning your PlayStation 4. We'll take you through everything you need to know, including what screwdriver you need to open the PS4 and how to clean the PS4's fan.

Warning: Take Care When Cleaning Your PS4

While this is a relatively straightforward process, you should still take care when taking apart and cleaning your PS4. The cleaning procedure doesn't require you to tear the system down much, thankfully.

We cannot be held responsible for any damage you may do to your system. It's a good idea to make sure you've backed up your saved data before proceeding, just in case.

With that out of the way, let's look at how to clean your PS4.

Step 0: What You'll Need for Cleaning a PS4

PS4 cleaning is a relatively simply job, but does require a few materials:

  • A TR9 Torx security bit screwdriver. The PS4 uses TR9 security screws. A TR8 screwdriver may work, but you should use a TR9 for best results. Make sure you get a screwdriver with a security bit, which has a tiny hole in the center.
  • A standard Phillips-head screwdriver. There are a few screws inside the PS4 that require this screwdriver to remove. A smaller screwdriver will work best here.
  • A knife or other sharp object. You'll want this to peel off the stickers covering the PS4's rear screws.
  • A can of compressed air. You'll need this to blow out the dust. You can purchase these online or at stores like Walmart.

For a more efficient cleaning, you may also want to use these optional materials:

  • Cotton swabs and/or cotton balls. If you'd like, you can use these to help you remove some of the dust. A cotton swab also helps you keep the fan from spinning. If you want to go above and beyond, try making some cleaning putty and using that instead.
  • A flashlight. It can be tough to see where the dust hides; a flashlight makes it easier to spot.
  • A paper towel or piece of tape to hold the screws. You don't want your PS4's tiny screws to go missing, so it's good idea to have somewhere to keep them. When removing the screws, you may want to place them in the same pattern you removed them, so you know which goes where.
  • A cleaning brush or old toothbrush. Dust caked onto the PS4's fan is difficult to remove, since the blade gaps are so small. A brush can scrape off whatever the canned air can't clear out.

Note that if you have an original model PS4, opening your console and cleaning it will void your warranty (which is valid for one year after purchase). However, you can remove the cover from the PS4 Slim and PS4 Pro models without voiding the warranty. Chances are that if you've had your PS4 for long enough that dust buildup is an issue, your warranty has probably expired anyway.

We'll show steps for cleaning the original PS4 in this guide (since it's the one I have, and the most complicated). At the end, we'll mention the differences for the other models.

Step 1: Shut Down Your PS4 and Unplug Everything

Before you start cleaning your PS4, make sure the console is turned off. It should have no lights on the top; if you see an orange light, then it's in Rest Mode (a low-power state) and you'll need to shut it down fully.

To fully shut down, turn your PS4 on, then press and hold the PlayStation button on your controller to open the Quick Menu. Head to Power > Turn Off PS4. Wait until all lights on your PS4 turn off, then unplug the power cable, HDMI cord, and anything else connected to it (like USB devices).

Bring your PS4 to a place where you have some room to work. Since you'll be removing small screws, you should have a safe place to set them.

Like when building a PC, you should take care not to build up static electricity. Don't work on a static-prone surface, such as a shaggy carpet, and try to only touch the plastic components when cleaning.

Step 2: Remove the Back Stickers and Screws

Now that you've got your PS4 ready to work, turn it around so the back is facing you, then flip it upside-down. You'll see three stickers along the "top" (which is really the bottom of the system, in line with the port for the power cable) that you must remove.

Note that if you have the slightly revised model of the original PS4, you'll only see one sticker and screw here in the middle.

The middle one has a special warranty sticker that damages itself when you remove it. The other two are a bit thicker and might require a bit of extra work to peel off. Use your knife or another pointed tool to peel back a corner of the stickers, then they should come off easily. Be careful not to scratch your system while you remove them.

Set them aside if you want to re-apply them later, or throw them out if you don't care. Once you've removed the stickers, use your TR9 screwdriver to remove the screws underneath. They're short, so they shouldn't require much effort. Take care not to strip them, and set them aside in a safe place.

Step 3: Remove the PS4's Cover

Now that you've removed the screws(s) holding the cover in place, you can pop it off. Start at the back (the part with the screws, facing you) and lightly pull up on the edges. Don't use a ton of force; as you work your way around the PS4, the cover should come free. Tug it up and remove it.

At this point, you can look at the cover you just removed and clean any dust inside. Your compressed air will make short work of it; this is also a good place to use a cotton ball to dab any remaining debris out. After cleaning the cover, set it aside for now.

Back on the system, you can now see the PS4's fan, which acts as a good indicator of how dusty your system is overall. However, there's one more component to remove first.

Step 4: Remove the Power Supply

You're nearly there! Now you just need to remove the power supply unit (PSU) so you can gain access to the heat sink and perform the most thorough cleaning. There are five screws holding the PSU in place. Three of them use the same TR9 security screws as the back cover, and the other two are standard Phillips head screws.

With the PSU on the side closest to you and the fan in the upper-right corner, the two Phillips head screws are at the edge of the system, to the far left and far right of the PSU. Use your TR9 screwdriver to remove the other three screws.

Note that if you're using the slightly revamped model of the original PS4, you'll see one screw in a different location here. The TR9 screw in the upper-left of the below photo will be a few inches above the TR9 screw at the bottom instead.

The Phillips screws are longer than the others and are a bit tougher to remove, so you may need to slide your knife or another thin object under the clips to pull them up. Take care to not bend the clips when doing this.

Now you can remove the PSU. There's a cable connecting it to the motherboard underneath, which you don't need to remove and don't want to accidentally unplug. Carefully grab the PSU by both sides and lift it up evenly. It may take a bit of wiggling to come free.

Once you've got it lifted up, gently "flip" it over the left side so it rests carefully, while staying plugged in.

Step 5: Blow the Dust Out of Your PS4

Finally, you have access to the PS4's heat sink and fan. Now we can explain how to clean your PS4's fan and remove dust that's deep in the system.

Take your can of compressed air and, if it has one, insert the straw for more focused cleaning. Spray a few blasts of air away from your PS4 first, in case there's any liquid in the tip.

Now, use your canned air to blow short bursts of air all around your PS4, getting rid of the dust. Make sure to check the corners for hidden dust (your flashlight can help here), and take care to blow it out of the system instead of further in. You can also use your cotton swabs or cotton balls to help you remove any dust the air won't reach.

Focus especially on the fan, heat sink, and outside edges of your PS4 when looking for built-up dust, as these are common locations for it. If you're not familiar, the heat sink is the metal set of "bars" that the straw is pointing at in the above picture.

Note a few important warnings when using canned air:

  • Never, ever hold the can upside-down. This will force the liquid inside the can out and could damage your PS4.
  • Do not spray compressed air directly into the fan. Spinning the PS4's fan at an extreme speed could damage the circuitry. Before you blow air near the fan, make sure you're either holding it with a finger or have jammed it with a cotton swab.
  • Use compressed air in ventilated areas only. Canned air can bother your skin and other body parts, and it's dangerous to breathe it in for an extended time.
  • Spray in bursts. Holding a steady spray of air will quickly cool the can, making it difficult for you to handle.

Step 6: Reassemble Your PS4

Once you're satisfied with your work cleaning out your PS4, it's time to put everything back together in reverse order.

First, carefully "flip" the power supply over and put it back in its spot. You'll notice two prongs in the bottom-left corner; make sure those line up with the gap in the PSU.

Replace the five screws holding the PSU in place. Remember that the two on the bottom-left and bottom-right are the longer Phillips head screws with clips. The other three are TR9 security screws.

Next, snap the cover back into place. Start from the front of the system (make sure you have don't have the cover backwards). Lightly press down all around the edges to the system to make sure it's secure. When done, it shouldn't wiggle.

Now, replace the TR9 screws on the back of the PS4. Take care not to damage them when screwing them back in. If you decided to keep the sticker(s) that cover the back screws, replace them now. The warranty sticker will appear scratched; this is by design.

Now your PS4 is all cleaned out and put back together, but there's an additional spot you might want to quickly check.

Step 7: Clean Your PS4's HDD Bay (Optional)

The PS4 has a separate compartment for the hard drive that may or may not have built up dust. It's not vital to check, but it's worth taking a moment while you have your system out.

To access it, lightly press and slide the shiny part of your PS4 cover (on the left when looking at it from the front) straight out to the left. This will remove the cover, allowing you to access the HDD bay.

A simple Phillips head screw adorned with the PlayStation button icons holds it in place. You can remove this, then pull the HDD to make room to clean out any dust in this area. Then just slide the HDD back in, replace the screw, and slide the cover on.

Step 8: Perform a PS4 Database Rebuild (Optional)

Now you can replace your PS4 and plug all your cables back in.

One last step isn't strictly necessary, but since you've just cleaned out your PS4's hardware, it's a good time to optimize its software performance too.

The PS4 includes a utility called Rebuild Database that optimizes all the data on your drive. It's essentially like defragmenting your computer. If you've had your PS4 long enough to build up significant dust, chances are it could benefit from this operation too.

To access it, shut down your PS4 (fully, so it's not in Rest Mode). Once it's off, press and hold the Power button on the front of the console (the top button). You'll hear one beep right away; continue holding it until you hear a second beep. This boots the PS4 into Safe Mode.

Connect your controller to the PS4 with a micro-USB cable, then press the PlayStation button to sync it. Select the Rebuild Database option and confirm the operation. Your PS4 will then perform the process.

The system says this could take some time depending on how much data you have. However, in our case it didn't take more than 15 minutes or so with nearly 2TB of data on our hard drive. Once it completes, you'll be back at your home screen.

This process doesn't delete any of your data, but it does have a few minor consequences. The PS4 will show you Discover notifications again for basic tips you've probably already seen. Your Home screen won't show your recently played games, so you'll have to track them down manually once. And your PS4 will also check for and run updates for games you haven't played in a while.

Once you've done this, you should hopefully notice your PS4 runs a bit smoother in the menus.

How to Clean the PS4 Slim and PS4 Pro

To clean the fan on the PS4 Slim, you don't need to remove the warranty sticker. It's much easier to remove the cover, too. All you have to do is pull up on the left and right corners on the front of your system. Pull on the middle, then slide the cover back and it will come right off.

From here, you'll be able to see the fan even though it's obstructed by a cover. If your fan doesn't look too dirty (a flashlight will help with this), you can spray some canned air into it and probably call it a day. Remember to use a cotton swab to prevent the fan from spinning.

For full cleaning, you'll need to remove several screws from the cover and the power supply plate. Since we focused on the original PS4 here, please see the video below for PS4 Slim-specific instructions.

The PS4 Pro is similar, but it's even simpler. Simply pull up on the front left and right corners to loosen the cover, then slide it back. You can see the fan as soon as you remove this, making basic cleaning quite easy.

Unfortunately, the heat sink is buried deep in the PS4 Pro, and accessing it requires disassembling almost the entire console. Thus, you should stick to just cleaning the fan if you have a PS4 Pro. Check the below video for more details.

Now Your PS4 Is All Clean

Now you know how to clean your PS4. You should notice it running much more quietly than it was before, especially if you've had the system for years. While you could clean even deeper into the system, doing so would require some potentially risky operations. It's better to avoid damaging your system and stick to this basic cleaning.

For future maintenance, take a brush, some compressed air, or cotton swab along the outside edges of your system to remove the dust once in a while. This should help prevent dust from building up inside, so you don't have to go through this process as often.

Some people have recommended placing plastic bottle caps or similar small objects under the four corners of your console. This lifts it off the below surface and should help with air flow. Aside from this, make sure your PS4 has room to breathe (keep it out of enclosed spaces). Paired with the above cleaning process when needed, your PS4 should stay cool and quiet.

To get even more from your PS4, there are other ways to boost the performance of the system.


8 Ways to Boost the Performance of Your PS4

While you can't upgrade your PS4 like a gaming PC, you can take these steps to experience the best performance possible.

Read Next

About The Author
Ben Stegner ( Articles Published)

Ben is a Deputy Editor and the Onboarding Manager at MakeUseOf. He left his IT job to write full-time in and has never looked back. He's been covering tech tutorials, video game recommendations, and more as a professional writer for over seven years.

More From Ben Stegner

Subscribe to our newsletter

Join our newsletter for tech tips, reviews, free ebooks, and exclusive deals!

Click here to subscribe

Remove Torx Security Screws WITHOUT special tools! Can help open/disassemble Playstation, Xbox, more

Fagots fuck in the ass- Well, mother, you give. Laughed. Women cant be fagots.

To ps4 screwdriver open

To the new. I was opposite her and looked into her eyes. She did not look away. Red beast.

How to take apart PS4 Controller and Repair the Analog Sticks

" And after all, she looked into the water: not even half an hour had passed before Columbine stepped awkwardly, her foot went along the grass and. The woman sat down with all swoop right on the most thorny bush. The dress was pulled up and did not protect the legs in the least.

You will also be interested:

He turned to me and lay down on me, kissing on the lips, running his hand down to the legs and thighs. I, in turn, hugged his neck. Guy started undressing me, saying how much he wanted me.

307 308 309 310 311